Jet ski accessories

vehiculier

Manufacturers

SPORT Graphic Kit for Kawasaki 15F jet ski Blue

KDK15FSB

RIVOT Racing

Complete SPORT Decoration Kit from RIVOT Racing for Jet Ski Kawasaki STX.. More details

Delivery within 2 to 10 days

399,95€ tax incl.

More info

Complete SPORT Decoration Kit from RIVOT Racing for Jet Ski Kawasaki STX 15F in Blue color

ref. KDK15FSB



PLEASE SAVE THE CUSTOMIZATION FIELDS AT THE BOTTOM OF THE PAGE

The decorative kits are made with an ultra-resistant vinyl, as well as a reinforced microbead glue and a special thick protection of 100µ. High Definition printing.

- Provides optimal protection for your case.
- Under the effect of heat, the vinyl takes shape and adapts to all the reliefs of your Jet-Ski for greater ease of installation.
- Retains the intensity of its colors for a long time even with strong UV exposure.


ENLARGE IMAGE in HD:


Necessary tools :
- A cutter or scissor
- A spray of degreaser
- A hair dryer or a heat gun (beware of high temperatures with the gun)
- A raclette
- A soft, clean cloth

Before starting to install your kit, make sure you are in favorable conditions: in a clean, dry place, temperature around 20°C and that you have enough time. Count 1 to 2 hours for the installation of a kit.


Step 1: Preparing the supports
Clean your fairings several times with a degreaser. It is imperative to remove all traces of glue and fatty substances from the plastics, even if they are new (silicone residues) because the glue will not adhere correctly. Be careful, products such as gasoline, white spirit or “WD40” type products can be effective on certain types of glue, but they are very greasy. Remember to degrease several times if you use it. Do not use window cleaners or acetone.


Step 2: Positioning and gluing
Position the sticker to identify its location. Always start a collage with the rough presentation of the piece to be glued. Little tip: the glue used is in the form of micro beads, this means that you can affix and deposit your sticker several times without it sticking permanently. Once you have chosen the appropriate location, all you have to do is scrape the sticker starting from its center which will have the effect of piercing the micro beads and thus triggering the bonding process by polymerization. Once the sticker is in place, remove the air bubbles by pressing very hard outwards with a clean cloth and/or a squeegee and/or felt.

Tip: If the part on which you are operating has significant relief, remember to slightly heat the sticker with a hair dryer, because under the effect of the heat the vinyl will take its shape and will apply more easily.


Step 3: Finishes
Finally, once the entire kit has been installed, slightly heat each piece using a hair dryer and apply significant pressure to the entire kit, with particular emphasis on sensitive areas, always using with a soft cloth or squeegee, from the inside out.


Step 4: Imperative!
Let your decoration kit rest for 2-3 days, no navigation!!! After the pressure exerted, the adhesive must have time to polymerize and marry its new support.


Tip: If you notice an air bubble, proceed as follows:
Prick the bubble frankly in its center using a pin, keep it pressed, heat
the bubble with the hair dryer then remove the pin while continuing to heat. hot air
dilated will thus evacuate on its own and the bubble will disappear.

Accessories

Other products in the same category

  • Daily Use Cover for JetBlaster (22+)
    Daily Use...

    Daily use cover for Yamaha JetBlaster jet skis...

    173,95€

  • Carpet for Seadoo RXP / RXP-X (06-11)
    Carpet for...

    Hydroturf mat for Seadoo RXP (06-11), RXP-X...

    159,95€

  • LINQ Base Installation Kit - PACK 3
    LINQ Base...

    LINQ Base Installation Kit - PACK 3 from Seadoo...

    83,95€

  • Black square Jetpilot stickers 8.5cm
    Black...

    Black square Jetpilot stickers 8.5cm ref. 13605

    1,95€

  • Original soft top for VX 110 Cruiser (05-14)
    Original...

    Original Yamaha Storage and Transport Covers...

    325,95€

  • Jettrim side protection for SXR 800
    Jettrim...

    Jettrim side protection for Kawasaki SXR 800...

    127,46€ -15% 149,95€

  • Roll of 1m x 1.50m camouflage red
    Roll of 1m...

    Roll of hydroturf mat 1m x 1.50m for jet ski...

    89,95€

  • Powder extinguishers 1kg for jet-ski
    Powder...

    Powder extinguishers 1kg for jet-ski ref....

    24,95€

  • Original Cover for Seadoo Wake PRO 215
    Original...

    Original Seadoo Wake PRO 215 Transport Covers

    353,95€

  • LINQ Retractable Water Ski Mast
    LINQ...

    LINQ Retractable Water Ski Mast from Seadoo for...

    424,95€

Product customization

After saving your customized product, remember to add it to your cart.

Text

loader

* required fields