Jet ski accessories

vehiculier

Manufacturers

RACE Graphic Kit for Ultra 300/310 Green

KDRKU300/310V

RIVOT Racing

Complete RACE Decoration Kit from RIVOT Racing for Jet Ski Kawasaki Ultr.. More details

Delivery within 2 to 10 days

449,95€ tax incl.

More info

Complete RACE Decoration Kit from RIVOT Racing for Jet Ski Kawasaki Ultra 300 and 310 in Green color

ref. KDRKU300/310V



PLEASE SAVE THE PERSONALIZATION FIELDS AT THE BOTTOM OF THE PAGE

The decorative kits are made with ultra-resistant vinyl, as well as reinforced microbead glue and special 100µ thick protection. High Definition Printing.

- Offers optimal protection for your case.
- Under the effect of heat, the vinyl takes shape and adapts to all the contours of your Jet-Ski for greater ease of installation.
- Retains the intensity of its colors for a long time even with strong UV exposure.


ENLARGE THE IMAGE in HD:


Necessary tools :
- A cutter or scissor
- A can of degreaser
- A hair dryer or heat gun (be careful of high temperatures with the gun)
- A raclette
- A soft, clean cloth

Before starting to install your kit, make sure you are in favorable conditions: in a clean and dry place, temperature around 20°C and that you have enough time. Allow 1 to 2 hours to install a kit.


Step 1: Preparing the supports
Clean your fairings several times using a degreaser. It is imperative to remove all traces of glue and grease from plastics even if they are new (silicone residue) because the glue will not adhere properly. Be careful, products such as gasoline, white spirit or “WD40” type products can be effective on certain types of glue, but they are very greasy. Remember to degrease several times if you use it. Do not use window cleaners or acetone.


Step 2: Positioning and gluing
Position the sticker to identify its location. Always start a collage with the rough presentation of the piece to be glued. Little tip: the glue used is in the form of micro beads, this means that you can affix and remove your sticker several times without it sticking permanently. Once you have chosen the appropriate location, all you have to do is scrape the sticker starting from its center which will have the effect of piercing the micro beads and thus triggering the bonding process by polymerization. Once the sticker is in place, remove air bubbles by pressing very hard outwards with a clean cloth and/or a squeegee and/or felt.

Tip: If the part on which you are working has significant relief, consider lightly heating the sticker with a hairdryer, because under the effect of heat the vinyl will take its shape and apply more easily.


Step 3: Finishes
Finally, once the entire kit is installed, lightly warm each part using a hair dryer and apply significant pressure to the entire kit, paying particular attention to sensitive areas, always using with a soft cloth or squeegee, from the inside out.


Step 4: Imperative!
Leave your decoration kit to rest for 2-3 days, no navigation!!! After the pressure exerted, the glue must have time to polymerize and adapt to its new support.


Tip: If you notice an air bubble, proceed as follows:
Prick the bubble squarely in its center using a pin, keep it pressed, heat
the bubble with the hairdryer then remove the pin while continuing to heat. The hot air
dilated will thus evacuate on its own and the bubble will disappear.

Accessories

Customers who bought this product also bought:

Other products in the same category

  • Blowsion arm spring for Superjet 96+
    Blowsion...

    Blowsion arm spring for Yamaha Superjet 96+...

    67,96€ -15% 79,95€

  • Steering box diameter 28.6mm red
    Steering...

    Universal Rick Roy red steering box for 28.6mm...

    390,95€

  • Solas floating smoke for jet ski
    Solas...

    Solas Smoke ref. PY600010

    38,21€ -15% 44,95€

  • Stapler Kit + STAINLESS STEEL Staples
    Stapler Kit...

    Stapler kit + INOX staples (1200) for fixing...

    34,95€

  • Foot storage bag for Yamaha SuperJet
    Foot...

    Foot storage bag for Yamaha SuperJet jetski...

    219,95€

  • Blue Square Bottle VP racing 20L
    Blue Square...

    VP Racing brand 20L Black Square quick filling...

    43,95€

  • LinQ Mounting Base Kit
    LinQ...

    LinQ mounting base set from Seadoo ref. :...

    87,95€

  • Universal saddle kit from 22 to 28mm
    Universal...

    Universal bridge kit from 22 to 28mm for...

    47,21€ -25% 62,95€

  • Seat cover for Wave Venture (94-96)
    Seat cover...

    Hydroturf seat cover for Yamaha WaveVenture...

    239,95€

  • Blowsion arm spring for Kawa. 800SXR
    Blowsion...

    BLOWSION ARM SPRING FOR KAWASAKI 800 SXR / 750...

    72,21€ -15% 84,95€

Product customization

After saving your customized product, remember to add it to your cart.

Text

loader

* required fields