Jet ski accessories

vehiculier

Manufacturers

SPORT Graphic Kit for Ultra 300/310 White

KDSKU300/310B

RIVOT Racing

Complete SPORT decoration kit from RIVOT Racing for Jet Ski Kawasaki Ul.. More details

Delivery within 7 days

449,95€ tax incl.

More info

Complete SPORT decoration kit from RIVOT Racing for Jet Ski Kawasaki Ultra 300 and 310 in White color

ref. KDSKU300 / 310B



THANK YOU FOR SAVING THE CUSTOMIZATION FIELDS AT THE BOTTOM OF THE PAGE

The decorative kits are made with an ultra resistant vinyl, as well as a reinforced microbead glue and a special 100µ thick protection. High Definition printing.

- Provides optimal protection for your case.
- Under the effect of the heat, the vinyl takes shape and adapts to all the contours of your Jet-Ski for greater ease of installation.
- Retains the intensity of its colors for a long time even with strong UV exposure.


ENLARGE IMAGE in HD:

In addition to this, you need to know more about it.

Necessary tools :
- A cutter or chisel
- A spray of degreaser
- A hair dryer or a heat gun (beware of high temperatures with the gun)
- A raclette
- A soft and clean cloth

Before starting to install your kit, make sure you are in favorable conditions: in a clean and dry place, temperature around 20 ° C and that you have sufficient time. Allow 1 to 2 hours for the installation of a kit.


Step 1: Preparation of the supports
Clean your fairings several times using a degreaser. It is imperative to remove all traces of glue and fatty substances from the plastics even if they are new (silicone residues) because the glue will not adhere properly. Be careful, products like gasoline, white spirit or “WD40” type products can be effective on certain types of glue, but they are very greasy. Remember to degrease several times if you use it. Do not use window cleaners or acetone.


Step 2: Positioning and gluing
Position the sticker to mark its location. Always start a gluing by the rough presentation of the piece to be glued. Little tip: the glue used is in the form of micro balls, this means that you can affix and deposit your sticker several times without it sticking permanently. Once you have chosen the appropriate location, all you have to do is scrape the sticker starting from its center, which will have the effect of piercing the micro balls and thus triggering the polymerization bonding process. Once the sticker is in place, remove any air bubbles by pressing very strongly outwards with a clean cloth and / or a squeegee and / or felt.

Tip: If the part on which you are operating has significant relief, consider heating the sticker slightly with a hair dryer, because under the effect of the heat the vinyl will take its shape and will be applied more easily.


Step 3: Finishes
Finally, once the whole kit is installed, warm each part slightly using a hair dryer and apply significant pressure to the entire kit, paying particular attention to sensitive areas, always using with a soft cloth or squeegee, from the inside to the outside.


Step 4: Imperative!
Leave your decoration kit to rest for 2-3 days, no navigation !!! After the pressure exerted, the glue must have time to polymerize and marry its new support.


Tip: If you notice an air bubble, do the following:
Prick the bubble frankly in its center using a pin, keep it pressed, heat
the bubble with the hair dryer then remove the pin while continuing to heat. Hot air
dilated will thus evacuate on its own and the bubble will disappear.

Accessories

Other products in the same category

  • Roll of 1m x 1.50m camouflage yellow
    Roll of 1m...

    Hydroturf carpet roll of 1m x 1.50m for jet ski...

    89,95€

  • MOOSE Racing jet-ski handles gray
    MOOSE...

    MOOSE Racing gray handles for jet-skis of all...

    14,95€

  • Cover (HT) GTI (06-08), GTI130/155, Wake155
    Cover (HT)...

    Hydroturf saddle cover, HT premier model for...

    379,95€

  • Complete marine fog horn 380ml
    Complete...

    Complete marine fog horn (horn + 380ml...

    14,95€

  • Cover FX HO Cruiser, SHO Cruiser (12-13)
    Cover FX HO...

    Hydroturf seat cover for Yamaha FX Cruiser HO +...

    429,95€

  • JOBE Foam Defense
    JOBE Foam...

    Defense Foam JOBE JOBE CONTOUR FENDER BLACK...

    26,95€ -10% 29,95€

  • SEA-DOO Fishing Seat
    SEA-DOO...

    Fishing seat from Seadoo for RXT, RXT-X, GTX,...

    884,95€

  • Seadoo Bilge Pump Kit for (18+) RXT/GTX/Wake Pro, (21+) RXP-X, (20+) GTI/SE/GTR, (19+) Fish Pro
    Seadoo...

    Original Seadoo bilge pump kit for Sea-doo...

    209,95€

  • Bilge pump kit for Seadoo Spark jet ski
    Bilge pump...

    Bilge pump kit for Seadoo Spark ref. 295100497

    208,95€

  • Carpet for Seadoo GTX (96-02) / GTI (97-00)
    Carpet for...

    Hydroturf mat for Seadoo GTX (96-02) / GTI...

    159,95€

Product customization

After saving your customized product, remember to add it to your cart.

Text

loader

* required fields