Subcategories
- For Seadoo 4-stroke watercraft with a 900 cubic centimeter engine: (see the correspondence table at the bottom of the page) - Solas Concord or Dynafly Series propeller, in high quality stainless steel and polished finish for better fluidity and less turbulence in the turbine. - Optimized for the best performance in both acceleration and speed.
COVERCRAFT TRANSPORT COVER for Seadoo watercraft Reference: COVERCRAFT-S
Supports for 3 jet ski fuel cans Reference: 52-4911
Hydroturf saddle cover, HT premier model for Seadoo Spark jet ski 2014 and above (2-seater model) Reference: AZ-SEW81
Hydroturf saddle cover, HT Premier model for comfort saddle on Seadoo Spark & Trixx jet skis from 2014 and above (2-seater model) Reference: AZ-SEW81T
Complete engine alignment kit from SBT for Seadoo Spark References: 80-103S
RIVA access hatch kit for Sea-doo SPARK 2 and 3 seats, this provides easy access to the engine compartment, without removing storage under the saddle and no visible modifications with the seat in place. Ref: RS4-130-EAK
IDIARTEC sand filter Ref: IDT-FAS Filter housing in marine quality aluminum machined from mass with stainless steel filter calibrated to stop impurities which risk clogging the engine cooling circuit. Delivered with straight and elbow brass fittings.
Riva stainless steel wear ring for seadoo Spark Reference: RS33-140-SK
Hydroturf saddle cover for Seadoo Spark 2014 and above watercraft (3-seater model) Reference: SEW811
Solas stainless steel wear ring for seadoo Spark Reference: SK-HS-140
IDIARTEC column for Seadoo SPARK Aluminum column machined from mass and black anodized Height 45mm, clamps tightened with stainless steel screws, handlebar clamping diameter 28.6 and diameter 22.2 with split reduction rings Ø 28.6 x Ø 22.2 Central hole for cable passage REF: CSS-45
Electronic trigger for Seadoo SPARK Aluminum trigger machined from mass and black anodized for electronic control Mounting on all Ø 22.2 SEADOO SPARK handlebars REF: GS-SP
Hydroturf saddle cover for Seadoo Spark jet ski 2014 and above (2-seater model) Reference: SEW81
Hydroturf saddle cover for comfort saddle on Seadoo Spark & Trixx jet ski from 2014 and above (2-seater model) Reference: SEW81T
Riva thermostat for Seadoo 4tec Ref: RS1013-50-1
Supports for 2 fuel cans for jet ski Reference: 52-4910
Hydroturf mat only available in 3M pre-glued for Seadoo Spark Trixx 2-seater watercraft from 2017 and up Ref. : HT812-PSA All Hydroturf Products are made to measure and individually. They require a minimum manufacturing time of 15 working days. They will not be returned or exchanged.
IControl lever from RIVA RACING for Seadoo watercraft equipped with an IBR ref. : RS24090-ICL
WATCON tool for re-pitching the Propellers ref. IMP-142 for 140 to 142mm propeller ref. IMP-148 for 144 to 148mm propeller ref. IMP-160 for 155 to 160mm propeller
High Compression Piston from EASY RIDER for Seadoo Spark Watercraft Ref: RS-5290
READ IT . ENGINE ALIGNMENT TOOL. ASSEMBLE ALIGN PLATE BRACKET KIT. (sea-doo all model)
Hydroturf mat only available in 3M pre-glued for Seadoo Spark 3-seater watercraft from 2014 and up Ref. : HT811-PSA All Hydroturf Products are made to measure and individually. They require a minimum manufacturing time of 15 working days. They will not be returned or exchanged.
Original outlet cap for mounting the WORX Exhaust System (Free Flow) for Seadoo Spark with outlet to be drilled Ref: WR04004-4
Hydroturf mat only available in 3M pre-glued for Seadoo Spark 2-seater watercraft Ref. : HT81-PSA All Hydroturf Products are made to measure and individually. They require a minimum manufacturing time of 15 working days. They will not be returned or exchanged.
Hydroturf mat only available in 3M pre-glued for Seadoo Spark Trixx 3-seater watercraft from 2018 and up Ref. : HT813-PSA All Hydroturf Products are made to measure and individually. They require a minimum manufacturing time of 15 working days. They will not be returned or exchanged.
Anti-spray bib in 60 inches or 152cm from Hydroturf for jet-ski Reference: TS03
Double switch (start & stop) from Idiartec for Seadoo watercraft from 2015 to 2019 Ref: CDS-15/19
Anti-cavitation kit for bailer Worx WR244 on Seadoo Spark 2014 and +. Ref: WR0707
Handlebar with NEKEN reinforced tube of 28mm in the center and 22mm at the end allowing the mounting of any type of handle Reference: 0601-3778
Reinforced handlebar NEKEN 28mm Yellow ref: 0601-3782
Handlebar with NEKEN reinforced tube of 28mm in the center and 22mm at the end allowing the mounting of any type of handle Reference: 0601-3780
Start & Stop switch bracket for Seadoo Spark jet ski ref. : RS2406015
ODI reinforced handlebar for saddle jet Reference: 06013082
Double switch (start & stop) from Idiartec for Seadoo watercraft from 2020 and above Reference: CDS-20
Handlebar with NEKEN reinforced tube of 28mm in the center and 22mm at the end allowing the mounting of any type of handle Reference: 0601-3329
Handlebar with NEKEN reinforced tube of 28mm in the center and 22mm at the end allowing the mounting of any type of handle Reference: 0601-3777
Handlebar with NEKEN reinforced tube of 28mm in the center and 22mm at the end allowing the mounting of any type of handle Reference: 0601-3776
Handlebar with NEKEN reinforced tube of 28mm in the center and 22mm at the end allowing the mounting of any type of handle Reference: 0601-2971
Worx brand start/stop switch for Seadoo Ref: WR06015
Lightened Timing Chain Sprocket from EASY RIDER for Seadoo 4-stroke watercraft Ref: RS-4221
Crankshaft Connector from EASY RIDER for Seadoo 300 watercraft with 1730cc engine Ref: RS-4391
Single Filter for Direct Intake Kit from WORX Racing for Seadoo Spark watercraft Reference: WR04026-5
Handlebar with NEKEN reinforced tube of 28mm in the center and 22mm at the end allowing the mounting of any type of handle Reference: 0601-3343
ENGINE ALIGNMENT SHAFT for Seadoo watercraft all models except spark and IS or AS Reference: 950-140
RIVA ANTI-CAVITATION KIT FOR SEADOO SPARK ON ECOPE RIVA RS22130 Ref: RS25130
Adaptable fuel injector from WSM or SBT (depending on availability) for Sea-doo 4-stroke jet-ski Reference: 006-620 / 006-621 / 006-622 / 006-623 / 006-624
IDIARTEC start and stop switch Ref: CSS
Valve seal kit from EASY RIDER for Seadoo 4-stroke watercraft Reference: RS-4220
Column extension for Seadoo H25, H50, H70, H100, H130 and H200 Reference: ES-25, ES-50, ES-70, ES-100, ES-130 and ES-200
Hood attachment set from RIVA Racing for jet-ski Reference: RY5-OLK
Engine Alignment Tool for Seadoo Spark ref. 80-103-05
Transmission Shaft Alignment Tool for Seadoo Spark Motorbike Ref. : 950-136
RIVA UNIVERSAL WATER FILTER Ref: RY1013-SDF-UK
Riva intake manifold ring for Seadoo Spark jetski Ref: RS12130-IMUK
Carrillo Replacement Multi-Phase Carrillo Bolt 8mm x 1.5 UHL Reference: BLT-CARR8M-1
Handlebar extension for Seadoo all models except Spark ref. : RS24100-BES
WORX support for DESS key switch for Seadoo Ref: WR06025
Exhaust Valve from PRO-X for Seadoo 4-stroke Watercraft 1500cc all models ref. : 28.5594-1